VENDesiccant
Home / Resources / Container Desiccant Dosage

Container Desiccant Dosage: How Many Bags for 20ft and 40ft

Calculation, reference quantities and placement for calcium chloride container desiccant.

"How many desiccant bags does a 20ft or 40ft container need?" is the question we get more than any other from importers shipping to the Gulf. There is no fixed answer — the right amount depends on the cargo, the voyage, the season and the climate at the destination port. This guide gives you the calculation to work from, reference quantities, and the few specification points that decide whether your moisture protection actually works.

Why the Quantity Is Not a Fixed Number

Desiccant only protects cargo if it absorbs moisture faster than the cargo and the container release it. The capacity you need therefore comes down to three variables:

For a well-specified calcium chloride container desiccant the industry rule of thumb is 1 kg per 2–4 m³ of container air, which is why our own calcium chloride packs run five 200 g sections to the kilo. That figure suits a standard voyage, but in real operation the cargo's own moisture load often dominates — which is why we recommend sizing by cargo, not by container volume alone.

One thing worth stating first: calcium chloride absorbs twice its own weight in water under ideal conditions, but ideal is all that is. In practice the physical limits of the box apply too, and our own measurements put a calcium chloride strip at roughly 140–180% of its own weight by the end of a voyage.

Calcium chloride container desiccant supplied as a 200 g five-section chain pack with a sample of the raw granules
Figure 1 — 200 g × 5 chain pack, one 1 kg unit: the format we supply for 20ft and 40ft containers.

Reference Quantities for 20ft and 40ft Containers

The table gives practical starting quantities for calcium chloride container desiccant, the standard choice for ocean freight. Use it as a baseline, then adjust for voyage length, cargo type and the humidity and temperature swing in the box.

ContainerInternal VolumeGeneral Cargo (reference)Hygroscopic Cargo (reference)
20ft (standard)~33 m³6–10 units of 1 kg10–16 units of 1 kg
40ft (standard)~67 m³12–20 units of 1 kg20–32 units of 1 kg
40ft High Cube~76 m³14–22 units of 1 kg22–36 units of 1 kg

These numbers assume a typical 20–30 day voyage in temperate-to-tropical conditions. For peak-season arrivals in the Gulf (June–September), or for very damp cargo such as green timber or leather, take the top of the range or go above it. They also assume a full container you control; consolidated LCL cargo needs a separate calculation.

Five-section calcium chloride container desiccant strip with a hook at the top, laid out on a wooden floor
Figure 2 — The five sections flex around obstructions, so one hook covers a long run down the side wall.

How to Estimate More Precisely

To build a specification that stands up, estimate the total water load first and then match it against desiccant capacity:

  1. Cargo moisture: cargo weight multiplied by moisture content (for example 20 tonnes of timber at 15% = 3,000 kg of water available).
  2. Air and packaging moisture: allow about 1 kg of water per 10–15 m³ of container volume for packaging and pallets.
  3. Desiccant capacity: a good calcium chloride unit takes up 140–180% of its own weight in water over a long voyage. Divide the total water load by the per-unit capacity to get the minimum number of units.
  4. Safety margin: add 30–40% for weather changes and port delays.

Placement Matters As Much As Quantity

Piling all the desiccant in one corner will not protect a container. To do any work it has to be spread out, acting on the air where condensation actually forms:

Calcium chloride container desiccant unit hooked onto a lashing ring inside a shipping container
Figure 3 — Hung on a side-wall lashing ring, clear of the cargo so air can reach it.

Calcium Chloride or Silica Gel?

For container shipping, calcium chloride is the default: high capacity, and it keeps absorbing even at high relative humidity. Silica gel suits sealed packaging (electronics, pharmaceuticals, food) where humidity is moderate and the pack is airtight. Many exporters use both — sachets inside the cartons, container desiccant on the walls — as layered protection.

Common Mistakes That Cause Claims

Get a Dosage Recommendation for Your Cargo

Tell us the container size, cargo type, weight and destination port, and we will work out the exact number of units for that cargo, that weight and that destination.

Specify Container Desiccants for Your Route

Send the cargo, container size and destination port and we will come back with the unit count and a price.

Related products and guides

💬 WhatsApp