VENDesiccant
Home / Resources / How Many Desiccant Bags per Container? A 20ft & 40ft

How Many Desiccant Bags per Container? A 20ft & 40ft Dosage Guide

The working formula, indicative quantities and placement rules for shipping to the Gulf.



"How many desiccant bags do I need for a 20ft or 40ft container?" is the question we get more than any other from importers shipping to the Gulf. There is no fixed number 鈥?the right quantity depends on the cargo, the voyage, the season and the climate at the destination port. This guide gives you a dosage table you can work from directly, a method you can run yourself, and the specification points that decide whether the system actually holds.

Why the Quantity Is Not a Fixed Number

Two things have to be true at once. The total capacity has to exceed every gram of water vapour that enters the container over the voyage, and the absorption rate has to keep pace with the rate at which that vapour appears. The first decides whether you have enough; the second decides whether it gets there in time. So the quantity is never a constant 鈥?three variables drive it:

One myth worth clearing up first: timber at 15% moisture content does not release 3,000 kg of water on a 20-tonne load. What actually migrates is the thin surface layer coming into equilibrium with the air in the box 鈥?typically under 0.1% of the cargo weight, around 20 kg on 20 tonnes. That is why dosage is sized from container volume and cargo type, not from moisture content.

For a well-specified calcium chloride container desiccant the industry rule of thumb is 1 kg per 2鈥? cubic metres of container air. The 4 m鲁 end covers general dry cargo; the 2 m鲁 end covers hygroscopic cargo or long voyages. On a 20ft box at roughly 33 m鲁 that works out at 8鈥?6 units of 1 kg (our strips run 1 kg each, five to a chain pack). It sits deliberately on the conservative side 鈥?treat it as a ceiling and take the working number from the table below.

One point usually left out of dosage guides: calcium chloride will take up twice its own weight in water under lab conditions, but a container is not a lab. Across space, airflow and temperature swings, our own measurements show the strips finishing a voyage somewhere between 140% and 180% of their dry weight. Every calculation on this page uses 140% 鈥?the cautious end.

Indicative Quantities for 20ft and 40ft Containers

The table gives practical starting quantities for calcium chloride container desiccants, the standard choice for ocean freight. Start from it, then move up or down for voyage length, cargo type and the temperature and humidity swing inside the box.

ContainerInternal VolumeGeneral Cargo (indicative)Hygroscopic Cargo (indicative)
20ft (TEU)~33 m鲁6鈥?0 units of 1 kg10鈥?6 units of 1 kg
40ft (FEU)~67 m鲁12鈥?0 units of 1 kg20鈥?2 units of 1 kg
40ft High Cube~76 m鲁14鈥?2 units of 1 kg22鈥?6 units of 1 kg

These figures assume a typical 20鈥?0 day voyage in temperate-to-tropical conditions. For peak-season Gulf arrivals (Jun鈥揝ep), or for very damp cargo such as green timber or leather, take the top of the range or one step above it. They also assume a full container you control; consolidated LCL cargo needs a different allowance.

How to Size More Precisely

The table covers most shipments. Where the cargo is unusual or the voyage is long, adjust in four steps:

  1. Take the baseline: read the range for your container size and cargo type off the table.
  2. Voyage adjustment: beyond 30 days, add 10鈥?5% for every extra 10 days.
  3. Safety margin: add 30鈥?0% for weather disruption and port delays 鈥?unless you already took the top of the table range, in which case that margin is priced in and must not be added twice.
  4. Ceiling check: run the rule of thumb (1 kg per 2鈥? m鲁) backwards. Whatever it returns is the ceiling; do not go far past it.

An example. A 40ft high cube carrying 25 tonnes of green timber to Dubai in August, 25 days at sea. First, the table gives 22鈥?6 units for hygroscopic cargo; the load is damp, so take the top 鈥?36. Second, 25 days stays inside the 30-day baseline, so no voyage adjustment. Third, the top of the range already carries the safety margin, so nothing is added. Fourth, the ceiling check: 76 m鲁 梅 2 = 38 kg, and 36 sits under it with a little room. The shipment goes out with 36 units.

If the check ever lands below the table figure, something in the inputs is wrong 鈥?the cargo is drier than assumed, or the pack format should be a larger unit. Running two methods against each other is how you arrive at a number that is neither reckless nor wasteful.

Placement Matters as Much as Quantity

Desiccant piled in one corner will not protect a full container. To do any work it has to sit where condensation actually forms:

Calcium Chloride or Silica Gel?

For ocean freight the default is calcium chloride: high capacity, and it keeps absorbing at high relative humidity. Silica gel suits sealed packaging 鈥?electronics, pharma, food 鈥?where the pack is airtight and humidity stays moderate; it is cleaner and will not leak. Plenty of exporters use both, sachets inside cartons and strips on the walls, as two layers of protection.

Common Mistakes That Cause Claims

Frequently Asked Questions

How many desiccant bags for a 40ft container?

12鈥?0 units of 1 kg for general dry cargo, 20鈥?2 for hygroscopic cargo. A 40ft high cube takes 14鈥?2 and 22鈥?6 respectively.

How much water does one 1 kg calcium chloride unit absorb?

Twice its own weight in theory. Under real ocean conditions our measurements come out at 140鈥?80%, and we size at 140%.

Can silica gel replace calcium chloride?

Inside sealed packaging, yes. For a full container, no 鈥?silica gel loses capacity sharply above 80% relative humidity and holds far less water per unit of volume.

How high should the units be hung?

Level with the cargo, or slightly above. Even spacing along the length matters more than height.

Get a Dosage Recommendation for Your Shipment

Tell us your container size, cargo type, weight and destination port and we will work out the exact count.

Related products and guides

💬 WhatsApp